Všechno
Klíčová slova výrobku
Zadejte prosím účet e-mailové adresy

Zákaznické recenze

4.84 out of 5
  • 27
  • 5
  • 0
  • 0
  • 0
Napište recenzi
  • Fabio
    Consigliata ma.....
    Ho scelto questa stampante (la mia prima stampante) soprattutto per il rinnovato style e i miglioramenti effettuati all'asse Z rispetto la sorella U20, qui infatti abbiamo un doppio motore sull'asse Z e per le poche prove che ho fatto fino ad adesso posso dire che dei soliti problemi letti in giro per i forum, qui neanche l'ombra.Il tutto è arrivato in un imballo impeccabile, l'interno della scatola è preformato e non c'era per i vari componenti la possibilità di muoversi durante il trasporto.Montata la stampante, mi sono accorto però che molte delle regolazioni e serraggi (anche dei pezzi montati dalla casa), avevano bisogno di una revisionata. Il piatto era praticamente lentissimo sul suo binario, cosi come le cinghie dei vari assi. I cavi scorrono dentro dei corrugati tagliati su un lato e in particolar modo quelli per l'asse Z soffrono molto quando si stampa all'altezza massima cioè 400mm.Serrato tutto sono passato all'accensione e al setup per trovare il giusto livellamento del piano. Qui mi sono subito accorto che qualcosa non va con l'asse Y, è come se la testina (e quindi l'estrusore) non riuscisse ad arrivare a corsa massima cioè a 300mm..... in verità sto ancora studiando la questione perchè in manuale posso muovermi liberamente su tutto il piatto, mentre in fase di livellamento o in fase di stampa questa cosa è più che evidente.Consiglio comunque vivamente questa stampante, solida e facilissima da montare, sono sicuro che una volta trovata la soluzione al mio problema (questione di giorni), saprà soddisfare tutte le mie esigenze.Brava Alfawise hai fatto centro anche stavolta ;-)

    Jul 07,2019

  • Игорь
    Принтер для ленивых
    Красивая и качественная игрушка. Сделано очень добротно, два синхронных вала, аккуратно упакованные провода, сенсорный цветной дисплей, печатает прямо из коробки. Все бы ничего, но....Драйвера шаговых двигателей не имеют радиаторов.Вентиляция потрохов вообще отсутствует.Головка паркуется не над столом (нужно колхозить удлинитель концевика).Вентилятор термобарьера слишком шумный.Прошивка только с флешкарты. Заявлено, что принтер прошит открытым исходным кодом Marlin - врут. Внести изменения, откалибровать шаги и поток, настроить принтер под себя, записать в память карту высот или подключить BLTouch НЕ ПОЛУЧИТЬСЯ. Если бы был выбор сейчас, то взял бы Alfawise U20 с вынесенным блоком, а лучше Tevo Tornado.А сейчас буду менять плату на SKR.К сожалению, порекомендовать этот товар могу тем, кто ищет в 3D печати только развлечение.

    Dec 03,2019

  • sophie
    Way Better Than Expected
    It's all together and getting ready to kick off the first print. This one took about an hour longer than the last because I was much more careful about making sure everything was square and tight. X axis belt is the trickiest part to do and I had a head start because I knew to thread it before I started assembling the X carriage. One screw was missing and the Z axis screws that hold the worm screw were all way too tight. Again, I knew to loosen them, so all was good.Great results and I look forward to adding it to my print rotation.

    Jun 24,2019

  • Hilary Flower
    great customer service!
    Very easy to assemble, the instructions were pretty clear. I assembled the printer to figure out how it all fit together, then I tore it apart to adjust everything and make sure it was square and level. Word of advice, double and triple check the adjustment of the V-wheels. I thought I had everything together pretty well, but I am starting to see some wear already on the wheels. This was no fault of the printer, I was eager to get some prints going and didn't check my work. I would highly recommend this printer for anyone.

    Jun 23,2019

  • Hogan Tony
    Awesome Printer
    I love this printer! Went together easy enough. Simple instructions. After getting it set up and printed a couple of upgrades it runs smooth and the prints look great. As a side note I had a small hiccup that was easily fixed, but the support team was on top of it. Offered a couple of fixes and I was able to get it sorted and back to printing in no time. Great support from the creality team. I know where I'm getting my next printer from.

    Jun 22,2019

  • m1rk00
    Almost excellent
    Publishing the firmware source of this printer would encourage people to buy it. The Alfawise U20 One is very simple to assemble, gives great results out of the box, but has some limitation getting higher experience. Retraction settings, accelerations, jerk, just to mention 3 of many factors that could be tweaked if firmware source could be published, AS written by Gearbest itself "open source marlin". A bigger community could be built around this and other Alfawise printers.

    Sep 23,2019

  • Bruno
    Excelente calidad de impresión, solo apretar un poco la cama y calibrar con el mismo programa y a imprimir.
    Tienen calibrado semi asistido, su formato es grande, además de que la pantalla es táctil, pero el tiempo de entrega fue una eternidad pero por logísticas de mi país ya gearbest envió en tiempo y forma, considero que el manual debería ser más extenso y más detallado es muy ambiguo, impresora altamente recomendada.

    Nov 06,2019

  • Rene
    Alfawise U20one - sehr guter Drucker
    Sehr schnelle Lieferung. Nach dem Öffnen des Pakets ging es an den Zusammenbau, was 5min dauerte. Nach dem ausrichten des Druckbettes, habe ich gleich eine Datei von der mitgelieferten sd Karte gedruckt und es funktionierte auch sofort. Danach cura installiert und ab da brauchte man schon ein bisschen Einarbeitung um gute Ergebnisse zu bekommen. Nach jetzt ca. 2 Tagen drückt er super gut auch mit cura und Co.

    Sep 30,2019

  • Beule
    Ein stabiler und trotz seiner Größe sehr kompakter 3D Drucker
    Der Alfawise U20 One ist trotz seines großen Druckbereichs (300 x 300 x 400) ein sehr kompakter Drucker geworden.Die Verarbeitung ist sehr stabil. Das Touch Bedienfeld ist sehr gut zu verstehen und im Gegensatz zum Anet Dreh Klick eine echte Bereicherung.Es waren ca 10Meter Filament mit dabei, damit man direkt mal was ausprobieren kann. Es hätte da ruhig etwas mehr sein können.Und seinen Preis ist es definitiv wert

    Oct 06,2019

  • Evan Sidney
    Great beginner printer at an outstanding price
    I would say you get great bang for the buck with this printer. Like many others I put a cheap mirror on it for a print surface. Prints better than a thousand dollar printer I have. Just realize that like any 3D Printer you can expect a certain amount adjusting all the time.

    Jun 28,2019